Pre-painted 2 mm Aluminum
Novelis ff2 pre-painted aluminum with a 2 mm thickness is developed specially for building facade cladding in ventilated and non-ventilated construction.
Coil-coated with high-quality PVdF paint, this pre-painted aluminum has a flawless, brilliant surface with a variety of plain, metallic and special colors available.
Resources
Contact Us
Click the button below to contact us for more information about Novelis Specialty Aluminum Products.

Protective Paints
To ensure color consistency and surface durability, our pre-painted 2 mm aluminum is coated in a continuous coil-coating process. Solid and metallic paints are applied in two or four coats, then permanently stove enameled.
For high-grade outdoor architectural applications, Novelis uses only PVdF (polyvinylidene fluoride) paints of the highest quality (80/20). With mainly inorganic pigments, these PVdF paints are ideal for outdoor applications. This helps protect the pre-painted aluminum to make the facade material weather resistant, UV resistant and seawater resistant.
With such protection, any type of environmental effects on the material is minimal. Extreme climate zones also do not pose a threat to the pre-painted aluminum surface.

Wider Spans, Higher Strength
The 2-mm panel thickness, with its AlMg3 alloy in temper H42 for facades, has similar span and fixing widths similar to AlMg1 alloys with a 3 mm thickness. This means that the weight of the aluminum facade material is reduced by a third and the same span width can be obtained with this lower material thickness. This helps minimize material handling, installation time and transportation costs.
Even in large surface applications under high stress, such as high-rise buildings with extreme wind loads, Novelis ff2 pre-painted 2 mm aluminum is an ideal solution. Building movement and temperature changes also do not pose a problem.

Colors
A wide range of colors with metallic, high-gloss and matte finishes are available. Copper tones, terracotta and stainless steel effects can also be applied. Custom colors are available on request.
PVdF coatings make surfaces easy to clean, so maintenance time is reduced. In contrast to polyester-coated aluminum cladding, ff2 repels dirt, and cleaning can be done with environmentally friendly warm water and neutral detergents.
Installation
Whether panels, flat sheets or cassettes are required, with ultra-flat or stress-free sheeting, ff2 works with both ventilated and non-ventilated cladding structures. The easy forming properties also make our material ideal for concave or convex shapes, corners, closures, column casing and other architectural details.
Excellent workability allows ff2 pre-painted 2 mm aluminum to be screwed, drilled, stamped, riveted, trimmed and bent without damage to the material or painted surface.
The lacquer on the reverse side of ff2 facade material is specifically designed for bonding. This means sheets can be adhesive-bonded to the substructure without visible attachments. Reinforcements can be bonded easily into cassettes.

Safety
Novelis pre-painted 2 mm aluminum has been certified in accordance with the latest DIN EN 13501 non-combustibility standards.
Under international building regulations, only non-combustible materials may be used in buildings exceeding a height of approximately 20 meters. This requirement applies no matter the height for public facilities such as nurseries, schools, airports, hotels and hospitals.
With Novelis ff2 receiving the highest A1 rating in combustibility tests, this means our pre-painted 2 mm aluminum can be used on any building of any height without restriction.
Sustainability
The coil coating process for Novelis pre-painted aluminum is environmentally friendly with all paints and lubricants processed in a closed material cycle. Non-hazardous pigments are used. This pre-painted aluminum is also free from heavy-metal erosion, is ground water neutral and can be recycled as a raw material without any loss in quality.
Architectural References (ff2® & ff3®)
Product Specifications
SPECIFICATIONS
Alloy
EN AW-5754 (AlMg3)
Temper
H42 according to EN 1396
Available thickness in mm
2.0
Available sheet width in mm
Up to 1500
Available sheet length in mm
Up to 3000
Other dimensions
On request
SURFACE FINISH
Available paint systems
PVdF (80/20), NWS, Fluorpolymer
Thickness of layer in µm
Approx. 24, metallics 30 – 40, back side approx. 3
Gloss level
Depending on color tone
TECHNICAL PROPERTIES
Weight in kg/m²
5.4
Permissible stress
Ợperm= 96 MPa to DIN 4113
Breaking elongation
A 50 > 9 %
Elongation limit
Rp 0,2 165 – 215 MPa
Tensile strength
Rm 220 – 260 MPa
Linear expansion
0,024 mm/m/°K
Elasticity
70.000 MPa
Corrosion resistance
Acc. to EN1396: 2007 : C.6.1.1/C.6.1.4
Protection film
XX µm removable up to 6 months after installation
FIRE SAFETY
Rating class
A1
According to DIN/EN
EN13501
CERTIFICATES
BBA
Yes
EPD Environmental Product Declaration
Yes
IBU
Yes
ECCA
Yes
ISO
Yes
Suitable for glued facade installation (DIBt)
Yes
TENDER INFORMATION
Tender information texts
Yes
CONSTRUCTION
Technical construction details
Yes
SUSTAINABILITY
Recycling content
up to 80 %
Recyclability
100%